Electricians & Plumbers in Canton, GA

Electrician is replacing old defective smoke detectors

Electrician installing emergency disconnect for well pump

Electrician is repairing handyman man work

Completed electrical rough-in work for the property. Installed and routed wiring for receptacles, switches, lighting, and other planned electrical components according to the layout. Installed electrical boxes, secured wiring, and routed circuits back to the appropriate panel locations. Inspected the rough-in work to verify proper placement, routing, and connections, leaving the electrical system prepared for the finish stage.

I successfully completed the electrical rough-in work for a new room, ensuring all planned electrical components were installed and routed correctly. This involved meticulously planning and installing wiring for all receptacles, switches, lighting fixtures, and dedicated circuits according to the room layout. I secured all cables, installed electrical boxes, and routed the wiring back to the appropriate panel locations. Each connection was verified for proper routing and adherence to safety standards. The electrical system is now fully prepared for the next phase of the finish installation.

Electrician starting basement wiring project

shut water off, replaced hose bibe checked for leaks. cleaned up work soce

Replaced the front exterior hose bib at the customer’s request due to dissatisfaction with the original hose bib that was previously installed. Once the new hose bib was installed, turned the water on and thoroughly checked the connection for leaks. No leaks were found, and the hose bib was operating properly. Cleaned and removed all debris from the work area upon completion.

electrician adding outlets

Arrived on site and found the existing hose bib on the back side of the house was dripping water. Shut off the water, removed the faulty hose bib, and installed a new hose bib. Once installation was complete, turned the water back on and checked the new connection for leaks. No leaks were found, and the hose bib is operating properly. Cleaned and organized the work area upon completion.

Installed the Halo 5 whole-house water filtration system. Once installed, filled and tested the system and checked all connections for leaks. No leaks were found. Began flushing the system to ensure proper operation and performance. Once the system was fully flushed, programmed the regeneration cycle for 12:30 PM every fourth day. Cleaned and organized the work area upon completion.

Electrician installing tesla charger

Electrician is installing a new smoke detector

Responded to a home in the Harmony on the Lakes community in Canton where the homeowner had finished converting the attached garage into a home gym over the spring and had been running portable units all summer because the central HVAC system never reached the space. Rather than trying to extend aging ductwork into the converted garage, installed a properly sized ductless mini-split, mounted the indoor wall unit for optimal coverage across the gym floor, set the outdoor compressor on a composite pad at the side of the garage, ran refrigerant lines and wiring through an exterior wall sleeve, and tested cooling through several demand cycles. Room went from unusable in the afternoon to comfortable in one visit.

Arrived on site and replaced the existing kitchen faucet and garbage disposal. After installation, the water supply was turned back on and the new faucet was thoroughly tested to ensure proper operation and verify there were no leaks. The sink was then filled and the garbage disposal was tested under load to confirm it was operating correctly and draining properly. All connections were inspected, everything functioned as intended, and the work area was cleaned before leaving the job site.

Electrician near me installing attic exhaust fan

Electricity giving free electrical estimate for attic fans

Arrived at a home in the Bridgemill community in Canton where a 14-year-old central AC system had finally given out during a heat wave. The compressor locked up and wasn't worth putting money into at that age. Did a proper load calculation for the house before recommending equipment size, pulled the old indoor coil and outdoor condenser, and installed a new high-efficiency matched Trane system with updated refrigerant lines. Charged to spec, balanced airflow through the existing ductwork, and ran full cooling cycles to confirm even delivery across every room. Homeowner said it was quieter and colder than the old unit had ever been; which honestly didn't surprise me at all.

giving a free electrical estimate for floodlight replacement

Electrician replacing defective outlet

Giving free electrical estimate to correct grounding

Arrived on site to diagnose hose bib that would not shut off completely. Inspected hose bib and operated valve multiple times to verify issue. Adjusted and worked valve until hose bib was able to shut off fully with no water continuing to drip. Verified proper operation and checked for leaks. Cleaned work area before leaving site.

Arrived on site to replace a faulty P-trap under the downstairs bathroom vanity sink that was causing leaks and improper drainage. Shut off water supply and removed the existing P-trap assembly. Inspected the drain line and confirmed no additional blockages or damage to surrounding piping. Installed a new properly sized P-trap, ensuring all connections were aligned and securely tightened for a leak-free fit. Restored water flow and tested the system by running the sink to verify proper drainage and confirm there were no leaks. Cleaned up the work area and ensured the vanity plumbing was functioning correctly before leaving.

Austin's call back

Completed replacement of a faulty angle stop valve at the downstairs bathroom vanity. Shut off the main water supply to the home and drained the system to ensure a clean and safe working environment. Removed the existing angle stop, which was worn and no longer functioning properly. Installed a new, high-quality angle stop valve and securely connected it to the existing water supply line. Reattached the faucet supply line and restored water service to the home. Carefully tested the new valve and all connections for leaks and proper operation. No leaks were found, and the new angle stop is functioning as intended with improved water control to the fixture. Work area was cleaned and left in good condition.