Electricians & Plumbers in Ringgold, GA

Arrived on site and located the issue with the underground 1-inch PVC water main. Excavated the affected area, exposed the damaged section of piping, and cut out and replaced the faulty PVC. Once the repair was completed, restored water service and pressurized the system to check for leaks and ensure proper water flow. Verified that the repair was holding with no leaks found. Backfilled the excavation and cleaned up the work area.

sent quote for undersized sewer

completed repipe

Upon inspection, we identified a screw that had punctured the PVC pipe, leading to a water leak. To address this, we removed a 1 ft. by 4 ft. section of drywall to access the damaged piping. The compromised section of the PVC pipe was carefully cut out and replaced with new piping. After completing the repair, we tested the system by running water to ensure proper flow and checked for leaks. No leaks were detected, and the system functioned correctly. The workspace was then cleaned, and all debris was removed.

3 inch sewer repair. plus drywall repair. quoted.

Completed an electrical service call to replace a broken wall switch. Removed the damaged switch, inspected the wiring and electrical box for any additional issues, and installed a new replacement switch with secure electrical connections. Tested the switch and connected lighting to verify proper operation. The repaired switch was left functioning safely and correctly.

Electrician, giving a free electrical estimate for full home re wire

Electrician correcting lighting circuit

Installed and configured a Ring Floodlight Cam to improve exterior security and property visibility. Completed mounting, electrical connections, camera setup, and system testing to ensure proper operation.

Electrician is installing a new panel

Electrician, giving a free electrical estimate for electrical service for building

A free electrical estimate for service upgrade

Got called to a home in the Poplar Springs area of Ringgold where the heat pump had been running in cooling mode all week but the house was sitting five degrees above the thermostat setpoint no matter what the homeowner set it to. Ran diagnostics and found the reversing valve was not fully seating in the cooling position, causing a partial bleed between discharge and suction that was killing real cooling capacity. Replaced the reversing valve, verified refrigerant pressures in cooling mode, and tested the system through several full thermostat calls to confirm it was reaching and holding the set temperature. Heat pump is working the way it should now.

Completed a professional water service installation today, providing a reliable upgrade to the property?s main water supply system. Removed the outdated line and installed a new water service line, ensuring proper depth, secure connections, and full code compliance for long-term durability.

Installed a new pressure reducing valve (PRV) to help regulate and stabilize the home?s water pressure. Removed the old, failing valve and replaced it with a high-quality PRV, ensuring all connections were secure and leak-free. Adjusted the valve to the proper pressure setting for optimal performance and to protect plumbing fixtures and appliances. Tested the system after installation to confirm consistent pressure throughout the home. Another successful plumbing service completed with improved water pressure control and reliability.

Dispatched to a home in the Battlefield Estates area of Ringgold after the homeowner said the heat pump had been blowing air that felt more like room temperature than cold, even with the thermostat set way down. Ran diagnostics and found a refrigerant leak at a flare fitting on the suction line that had brought the charge down enough to kill real cooling capacity. Repaired the fitting, pressure-tested the repair with nitrogen, pulled a vacuum, and recharged the system to manufacturer specification. Checked the temperature split across the evaporator before calling it done. Came in right where it needed to be. Homeowner said it felt like a completely different house on the way out to the truck.

Electrician installing panel surge protection

Completed a service call to install a new outdoor hose spigot and repair a leaking 1-inch water line. Removed the old, worn hose bib and installed a new, durable spigot to ensure reliable outdoor water access. Located and repaired a leak on the 1-inch water line, restoring proper water flow and preventing further water loss. System was fully tested after repairs to confirm there are no leaks and everything is operating correctly. Another successful plumbing repair completed with quality workmanship and attention to detail.

Electrical Installation: Installed a customer-supplied outdoor ceiling fan on a covered patio at a residential property. Verified the existing electrical box and circuit were rated for exterior fan use, mounted the weather-resistant fan assembly, and completed all wiring connections according to manufacturer specifications. Tested fan operation, speed settings, and integrated lighting to ensure safe performance and proper airflow throughout the outdoor seating area.

Completed a professional plumbing service installing a new sewer ejector pump to ensure reliable wastewater removal from the property. The old unit was removed and replaced with a high-performance ejector pump, restoring proper drainage and preventing potential backups. If you're searching for ejector pump installation or sewer pump repair near me, we provide fast, dependable plumbing solutions to keep your system running smoothly.

Completed a 3.5 ton gas pack unit replacement for a homeowner today. Removed the old, inefficient system and installed a new high-efficiency gas package unit to improve heating and cooling performance, airflow, and overall energy savings. Ensured all electrical, gas, and duct connections were properly secured and tested for safe operation. System is now running strong and ready for the upcoming seasonal demands. Another reliable HVAC installation done right.

Completed replacement of an existing hose bib due to wear and leakage issues. Shut off water supply, removed the faulty unit, and installed a new, code-compliant hose bib. Ensured all connections were properly sealed and secured. Restored water service and tested for leaks and proper operation—no issues found. Verified adequate water flow and functionality. Work area was cleaned and left in good condition.

Removed existing 50-gallon gas water heater and properly disconnected gas, water, and venting connections. Installed new 50-gallon gas water heater, ensuring all connections meet current plumbing and gas code requirements. Upgraded fittings and installed new water supply lines as needed for a secure and leak-free installation. Installed new shut-off valve and ensured proper gas control connection with leak testing performed. Verified proper venting and draft for safe operation. Filled and pressurized system, then tested unit for proper heating and performance. Checked for leaks on all connections and confirmed system is operating efficiently. Cleaned up work area and disposed of old unit.

Replacement of faulty breaker in panel

Completed a professional plumbing service installing a new P-trap under a kitchen sink for a local homeowner. The existing trap was outdated and causing slow drainage and minor leaks. We removed the old assembly and installed a properly fitted P-trap to ensure optimal drainage and prevent sewer gases from entering the home.