Electricians & Plumbers in Marietta, GA

Completed a backflow preventer replacement on a Navien tankless water heater. The existing backflow device was failing and no longer providing proper protection to the potable water system. Shut off the water supply, safely removed the defective backflow preventer, and installed a new code-compliant backflow device.

We’re currently in your area installing a brand-new high-efficiency HVAC system to help a local homeowner enjoy better comfort and lower energy bills.

Provided an on-site estimate for a lift station installation. Assessed the property layout, existing sewer line conditions, discharge location, and elevation requirements to determine proper pump sizing and basin capacity. Discussed options for a residential sewage lift station system, including grinder pump vs. ejector pump, control panel setup, check valve installation, and alarm system for high water protection. Prepared a detailed quote covering excavation, basin installation, pump system, discharge line tie-in, electrical coordination, and final testing. Reviewed scope of work and answered all customer questions regarding timeline, permitting, and warranty.

Came out and relocated an existing gas line to a new location for proper appliance connection and safety. Secured and tested the line to ensure there were no leaks and that everything was up to code. If you need gas line relocation or installation, call us for fast and reliable service in your area.

came out and changed out the check valve for a Navien tankless water heater to restore proper operation and prevent backflow issues.

Came out and installed a new gas water heater for the customer. Removed the old unit, installed the new gas water heater, connected water and gas lines, and ensured everything was up to code. Tested the system for leaks and proper operation. Customer now has reliable hot water again.

came out and replaced an old gas water heater with a new, efficient unit. Verified proper gas connections, venting, and water lines, and tested the system to ensure everything is running safely and efficiently. Customer now has reliable hot water restored.

Completed installation of a customer-supplied kitchen faucet. Removed the existing faucet and disconnected old supply lines. Cleaned mounting surface and properly secured the new faucet assembly to ensure a tight, leak-free fit.

Completed a service call to clear a clogged main drain line by professionally augering the line to restore proper flow and drainage throughout the home. After removing the blockage, pulled the toilet to ensure full access and proper clearing of the line. Reset the toilet with a new wax ring and hardware to ensure a secure, leak-free seal.

Completed plumbing repairs at a residential property including removal and replacement of a faulty angle stop at the kitchen sink. Installed a new quarter-turn angle stop to ensure reliable shut-off and improved water control. Replaced an outdated valve with a new ball valve for better durability and smoother operation on the water supply line. Cut out and replaced a leaking solder tee fitting, properly cleaned, prepped, and soldered connections to restore full integrity of the copper piping system. Tested all connections under pressure to confirm no leaks and proper water flow to the kitchen sink. System is operating correctly.

Responded to service call for a damaged 3/4” main water supply line. Located the compromised section and shut down the water to the home to prevent further leakage. Removed the damaged portion of pipe and installed new 3/4” piping with proper fittings to ensure a secure and long-lasting connection. Restored water service, pressurized the system, and tested thoroughly for leaks. Confirmed proper water flow and pressure throughout the home. Repair completed successfully and system is operating as intended.

Responded to service call for a damaged 3/4” main water supply line. Located the compromised section and shut down the water to the home to prevent further leakage. Removed the damaged portion of pipe and installed new 3/4” piping with proper fittings to ensure a secure and long-lasting connection. Restored water service, pressurized the system, and tested thoroughly for leaks. Confirmed proper water flow and pressure throughout the home. Repair completed successfully and system is operating as intended.

Arrived on site to address a failing gate valve on the main water line. The existing valve was worn and not shutting off water properly. Shut down water supply and drained the line to perform repair. Removed old gate valve and installed a new quarter-turn ball valve for improved reliability and easier operation. Secured all fittings, restored water service, and tested for leaks and proper function.

Checked in to replace a leaking house bib (outdoor hose spigot) at the home. Shut off the water supply, removed the old damaged hose bib, and installed a new frost-free house bib with proper fittings and sealant. Restored water, tested for leaks, and verified proper operation and water pressure. Area was cleaned up and system left in good working condition.